Kulak Kent Sitesi
English
u Protect the measuring tool from moisture and direct Measuring process
sunlight.
Once switched on, the measuring tool is in the length meas-
u Do not expose the measuring tool to any extreme tem- urement function. For a different measuring function, press
peratures or variations in temperature. For example, the button (13) [Func]. Use the button (4) [+] or the button
do not leave it in a car for extended periods of time. In (11) [–] to select the required (see "Measuring functions",
case of large variations in temperature, allow the measur- page 28). Activate the measuring function with the button
ing tool to adjust to the ambient temperature before put- (13) [Func] or with the measuring button (2) [ ].
ting it into operation. The precision of the measuring tool
Once the measuring tool has been switched on, the rear
may be compromised if exposed to extreme temperat-
edge of the measuring tool is selected as the reference level
ures or variations in temperature.
for measurement. Changing the reference level (see "Select-
u Avoid substantial knocks to the measuring tool and ing the reference level (see figure A)", page 26). Apply the
avoid dropping it. Always carry out an accuracy check measuring tool to the point at which you want to start the
before continuing work if the measuring tool has been measurement (e.g. wall).
subjected to severe external influences Accuracy Check Note: If the measuring tool has been switched on using the
of the Measuring Tool.
on/off/delete button (9) [ ], briefly press the measuring
u The measuring tool is equipped with a wireless inter- button (2) [ ] to switch the laser on.
face. Local operating restrictions, e.g. in aeroplanes
To initiate the measurement, briefly press the measuring
or hospitals, must be observed.
button (2) [ ]. Then the laser beam is switched off. For a
further measurement, repeat this process.
Switching On/Off
With the laser beam continuously switched on and when in
During work, ensure that the reception lens (20), the laser the continuous measurement function, the measurement be-
beam output (18) and the camera (19) are not closed off or gins the first time you press the measuring button (2) [ ].
covered, otherwise correct measurement will not be pos-
u Do not direct the laser beam at persons or animals and
sible.
do not stare into the laser beam yourself (even from a
– To switch on the measuring tool and the laser, briefly distance).
press the front or side measuring button (2) [ ].
Note: The measured value typically appears within half a
– To switch on the measuring tool without the laser, briefly second, and no later than approximately four seconds. The
press the on/off/delete button (9) [ ]. duration of the measurement depends on the distance, the
u Do not direct the laser beam at persons or animals and lighting conditions and the reflective properties of the target
do not stare into the laser beam yourself (even from a surface. Upon completion of the measurement, the laser
distance). beam is automatically switched off. The continuously
To switch off the laser, briefly press the on/off/delete but- switched-on laser beam is not switched off after the meas-
ton (9) [ ]. urement (see "Continuous laser beam", page 27).
To switch off the camera, press the camera button (10).
Selecting the reference level (see figure A)
To switch off the measuring tool, press and hold the on/off/
delete button (9) [ ]. You can choose between four different reference levels for
The measured values and device settings in the memory are the measurement:
retained when you switch the measuring tool off. – The rear edge of the measuring tool (e.g. when placing
against walls)
Camera – The tip of the measuring pin (8) folded by ° (e.g.
Switching on the measuring tool automatically switches on when measuring from a corner)
the camera (19). To switch it off, press the camera button – The front edge of the measuring tool (e.g. when measur-
(10). ing from a table edge)
For larger distances (of approx. more than five metres), a – The centre of the thread (17) (e.g. for tripod measure-
target marker is also superimposed to mark the measuring ments)
point. The folding out and in of the measuring pin (8) by ° is de-
tected automatically and the appropriate reference level is
Optimising visibility of the laser point
suggested. Confirm the setting by pressing the measuring
Especially when using the measuring tool outdoors, in sun- button (2) [ ].
light and also over long distances indoors, the laser point
Select the settings for the measuring tool using the soft key
may not be visible. The visibility of the laser point/measure-
(3) [ ]. Use the button (4) [+] or the button (11) [–] to
ment point can additionally be improved in order to connect
select the reference level and confirm this by pressing the
the camera by:
button (13) [Func].
– Setting the display brightness (tool settings)
The rear edge of the measuring tool is automatically preset
– Using the zoom by pressing the button (5).
as the reference level every time the measuring tool is
switched on.
1 92A 4F4 9
(25)
2
(26)
1 M00 05B
(27)
BT
0 B00